Home   Mini USB Extender Kit
Model: VUSBU100K
USB Hub Extender Kit
Model: VUSBU100HK
 
Host Unit - Tx
Remote Unit - Rx
Host Unit - Tx
 Remote Unit - Rx
 
VUSBU100K is a passive device using UTP cabling to extend single USB connection at a distance up to 300 ft / 100m. VUSBU100HK is a passive device using UTP cabling to extend single USB connection and providing two port hub functions at a distance up to 150ft / 50m. These devices are consisted of two parts, a host and a remote unit. They can support USB 2.0, and 1.1 full and low speed devices with real-time transmission without delay. VUSBU100K is ideal for use with i.e.: mouse and keyboard and VUSBU100HK is ideal for use with i.e.: digital camera and printer. Any UTP cabling (UTP/FTP/STP CAT5/5e/6) can be used. Both devices have RJ45 jacks for easy cabling and secure connection. Both devices offer a very small foot print, PnP installation without the need to install any drivers. They also have added protections against lightning power surge and electrostatic discharge.
     
VUSBU100K Features: VUSBU100HK Features:
• USB 2.0, USB 1.1 Full Speed transmission up to 100ft / 35m
• USB 2.0, USB 1.1 Low Speed transmission up to 300ft / 100m 		• USB 2.0, USB 1.1 Full Speed transmission up to 150ft / 50m
• USB 2.0, USB 1.1 Low Speed transmission up to 150ft / 50m
• Dual output giving the user added capability to add more devices
   
Application Diagram:
 
VUSBU100K
 
VUSBU100HK

VUSBU100HK Panel View:
  Parts Description
1 USB-B Type Port Using USB-B to A Male to Male cable to PC
2 USB-A Type Port USB-A Male for device connection
3 RJ45 Jack Port RJ45 connection between Host to Remote unit

 

VUSBU100HK Installation Steps:

Please check all equipments and accessories before installation, if there are missing parts please contact your supplier.
  • One VUSBU100HK Host unit
  • One VUSBU100HK Remote unit
  • One USB-A to USB-B Male to Male cable
  • This installation manual
Please follow the steps below for a proper installation
  1. Connect the Host unit USB-B port to the USB-B Male to USB-A Male cable than connect the USB-A Male connecter to the PC.
  2. Connect the device like USB Mouse and Keyboard to the Remote unit.
  3. Now connect the previously prepared RJ45 Modular jack to both units.
  4. Check to see if the LED Green Power light is on, power is provided to the device when green light is on. Now you have successfully completed the installation.

Specification:
Model
VUSBU100K
VUSBU100HK
Connectors Host Unit
Input / Output
1 X USB A Type Male Port / 1 X RJ45 Port
1 X USB B Type Port / 1 X RJ45 Port
Remote Unit
Input / Output
1 X RJ45 Port / 1 X USB A Type Female Port
1 X RJ45 Port / 1 X USB A Type Port
Transmission Properties Transition Distance
USB 1.1 Low Speed up to 300ft / 100m
USB 1.1 Low Speed up to 150ft / 50m
USB 2.0 Full Speed up to 100ft / 35m
USB 2.0 Full Speed up to 150ft / 50m
LED Power LED
1 Green
Protection Transient Protection
1KV : IEC61000-4-5 (GB/T 17626.5)
Electrostatic Discharge
1a Contact Discharge level 3
1b Air Discharge level 3
IEC61000-4-2 (GB/T 17626.2)
Stability MTBF
> 10000 Hours
Physical Properties Dimensions
(L x W x H)
7.87” x 1.38” x 0.89”
200mm x 35mm x 22.5mm
(including cable)
3.34” x 2.16” x 0.89”
85mm x 55mm x 22.5mm
Housing Material
ABS Plastic
Metal
Color
Black
Net Weight
0.15 lbs / 70g
Host Unit: 0.35 lbs / 160g
Remote Unit: 0.37 lbs / 168g
Environment Operation Temperature
32°F ~ 131°F / 0°C ~ 55°C
Storage Temperature
-4°F ~ 176°F / -20°C ~ 80°C
Relative Humidity
0 - 95% (non-condensing)
*Specifications are subject to change without notice.
 
USB supports the following data rates:
  • The Full Speed rate of 12 Mbit/s (1.5 MB/s) is the basic USB data rate defined by USB 1.1. All USB hubs support Full Speed, and such as USB memory drives.
  • A Low Speed rate of 1.5 Mbit/s (187.5 kB/s) is defined by USB 1.0. It is very similar to full speed operation except that each bit takes 8 times as long to transmit. It is intended primarily to save cost in low-bandwidth Human Interface Devices (HID) such as keyboards, mice, and joysticks.
  • A High-Speed (USB 2.0) rate of 480 Mbit/s (60 MB/s) was introduced in 2001. All high-speed devices are capable of falling back to full-speed operation if necessary.
Troubleshooting:
The following steps might help you resolve some installation issues:
  • Make sure the equipment is installed according to the manufactures installation guide.
  • Check both end of the cable to make sure they are using the same cabling standards B to B or A to A.
  • Make sure the device used with unit confirmed to the USB 2.0 full speed or lower standard.
  • Check to make sure the actual distance between the host and remote unit doesn’t exceed maximum cable length and speed.
  • Check to make sure the cable is in working and good condition.
  • Using a known good working unit to replace the unit in question to help determent if it is defective.
  • If all of the above can’t resolve the problem, please contact your supplier for technical support.
How to make a RJ45 Modular Jack:
Pin
T568B
Pair
T568B
Character

1
2
White/Orange Stripe
Video +

2
2
Orange Solid
Video -

3
3
White/Green Stripe
Power -

4
1
Blue Solid
Power -

5
1
White/Blue Stripe
Power -

6
3
Green Solid
Power +

7
4
White/Brown Stripe
Power +

8
4
Brown Solid
Power +
Wrongfully mixing the colors may result in burning the device.
Important Note:
  • Be sure to use good quality CAT 5E 350Mhz or better cable.
  • When using RJ45 Standard EIA/TIA568A or B on one end of the cable the other end must use the same standard to match it. Otherwise the system will not work.
  • Making sure not to reverse the transmitter and receiver, it will not work if reversed. The unit at the PC side is defined as the transmitter.
  • When the device is in operation DO NOT un-plug the RJ45 jack from the transmitter or the receiver unit. Power off the system before un-plugging.
  • Low Speed USB 1.1 transmission can reach 300ft / 100m, device like mouse and keyboard. Full Speed USB 1.1 transmission can reach 150ft / 50m, device digital camera and printer.
  • When adding a USB Hub at the receiver end, the transmission range will reduce to 100ft / 35m.

RoHS
B-27, B-28

OKINA USA Cabling Systems and Solutions provides an answer for all your cabling needs. Our complete line of baluns allows you to easily extend your current audio/video/data system up to 1200ft and even up to 8000 ft, with an active balun.

OKINA USA Baluns are perfectly suited for applications such as these:
CCTV Security Systems
CCTV Surveillance Systems
CCTV Cameras
Home Theatre
LCD/CRT Monitors
Televisions
VGA Monitors
DVD Players
PCs (Personal Computers)
Laptops/Notebooks
USB and PS/2 Devices
UTP (Unshielded Twisted Pair Cable)
BNC (Coaxial Cable)

How does a balun work?
Baluns are used to convert between "Balanced and Unbalanced" electrical signals.
Baluns work by transforming the original unbalanced (video/power/data/etc) signal to a balanced frequency used by a different cable, like CAT5 UTP. Not only does this reduce interference, but it also allows you to transmit a signal much longer than the original application would allow. Baluns are always utilized in pairs. One balun is needed to convert the original signal to a new frequency, and another balun is used at the other end to revert to the original frequency.

"Passive" Video Baluns do not require power, and can extend a signal up to 2000ft (B/W)
"Active" Video Baluns require power, but can extend a signal up to 8000ft (B/W)